CMA Dishmachines AHS Especificações

www.cmadishmachines.com

Getting Started 2.3.5. Pump Impeller Note Figure 2.2.5 Installation: When installing the water pump impeller the Nylon Lock Nut indicated by

Getting Started 2.3.6. Optional Hood Adapter (set of two) An optional Hood Adapter set (P/N 13901.82) is available. The dimensions for proper inst

Getting Started 2.3.7. Optional Freestanding Scrap Trap and Adaptor Kit The optional Freestanding Scrap Trap (P/N 01560.00) and Adaptor Kit (P/N 13

Getting Started 2.3.8. Field Installed Accessories Installation of the accessory chemical pumps must be performed by qualified personnel. 2.3.8.1.

Getting Started 2.4. Safety Tips for the CMA-66 DANGER: Always turn off the circuit breaker at the wall when working on this dishmachine. Even wit

Operation 3. Operation 3.1. Initial Setup 3.1.1. Auto Fill Timer/ Auto Re- Fill Timer Both timers for the CMA-44 are set at the factory, but may

Operation Note: If at any time less than a full Auto Fill cycle is desired with the IDEC brand timer, the Auto-Fill can be interrupted (stoppe

Operation 3.2. Beginning Operation To run the dishmachine, perform the following steps: 1. Close both drains (valve handles in vertical position

Operation 6. At the end of the shift and after heavy periods of accumulation, clean the three strainer trays inside the machine. Also, at the

Operation The sanitizing pump operates when the fresh water enters the machine during final rinse. The water is treated at 50 PPM (parts per mill

Table of Contents CMA-66 1. SPECIFICATIONS... 2 1.1 C

Operation 6. Replace all the strainer trays into their proper position and fill the machine. 7. Place a rack into the machine and observe the

Operation 3.4. Quick service guide MODEL CMA-66 Installation & Operation Manual Rev. 1.09 B

Operation 3.5. Trouble Shooting PROBLEM LIKELY CAUSE SOLUTION Pre-wash/power wash motor inoperative Bad motor or capacitor Faulty contactor Repla

Customer Notice 4. CMA-66 Customer Notice MODEL CMA-66 Installation & Operation Manual Rev. 1.09B

Customer Notice TIPS TO SAVE A SERVICE CHARGE If the Lessee of this equipment initiates a service call and it is subsequently determined that the pr

Electrical Diagrams 5. Electrical Diagram MODEL CMA-66 Installation & Operation Manual Rev. 1.09B

Operation MODEL CMA-66 Installation & Operation Manual Rev. 1.09 B

Operation 7. Electrical Diagram CMA-66 480/575/600 V MODEL CMA-66 Installation & Operation Manual Rev. 1.09 B

1. Specifications CMA-66 L.T. CMA-66 H.T. 1.1 CMA-66 WATER CONSUMPTION PER RACK .8 GAL. .94 GAL. PER HOUR 192 GAL. 192 GAL. CONVEYOR SPEED FEE

Getting Started 2. Getting Started 2.1. Introduction to CMA-66 The CMA-66 is designed to give maximum cleaning in 66 inches. It represents the cle

Getting Started 2.2. Receiving and Installation When you receive your new CMA-66, complete the assembly by installing the scrap tray assembly with

Getting Started 2.3. Receiving and Installation (Old Models) When you receive your new CMA-66, complete the assembly by installing the scrap tray a

Getting Started 2.3.1. Electrical* A 3-phase 208-240 volt AC, 60 Hz dedicated circuit should be used to supply electrical energy to the CMA-66 dish

Getting Started P/N 13505.10 205 RACKS (CMA-44H) 242 RACKS (CMA-44L) P/N 13505.12 OLD M

Getting Started 2.3.4. Scrap Tray Assembly and Overflow Chute Installation The scrap tray assembly and overflow chute, which came packaged inside t